Critical/SPS

Critical Water Sampling at POUs Under ST108: Where, How, and How Often?

Gloved hand collects a Critical Water sample at a sterile processing outlet

A water sample can tell you a lot about your system. But are you collecting it from the right place?

In sterile processing, Critical Water quality matters at every stage, from treatment to the point where water comes into contact with medical devices.

ANSI/AAMI ST108:2023 establishes a standard for water quality management, including routine monitoring and sampling. Understanding where to collect samples, which parameters to test, and how often to monitor them helps facilities make better use of their testing results.

Where Should Critical Water Samples Be Collected?

A water treatment system may produce water that meets the required specifications, but that doesn’t necessarily mean the same quality is maintained throughout the distribution system.

As Critical Water moves through storage tanks, piping, and equipment, conditions can change.

ST108 addresses monitoring at two important stages:

  • Point of generation (PoG): Monitoring after treatment helps evaluate the water being produced and distributed.
  • Point of use (PoU): Monitoring where water is delivered helps verify the quality available for medical device processing.

Additional sampling locations may be necessary based on system complexity, less frequently used outlets, previous results, and facility-specific risks.

How Often Should Critical Water Be Tested Under ST108?

One of the most practical parts of ST108 is its guidance on routine water quality monitoring.

Table 4 ANSI/AAMI ST108:2023 specifies quality monitoring requirements, while Table 6 outlines recommended minimum monitoring frequencies at the point of water use.

The following simplified reference summarizes its recommendations for Critical Water at points-of-water-use.

Critical Water Routine Monitoring: ST108 Tables 4 and 6 Summary

Parameter Routine sampling location Minimum frequency Unit Requirement
pH @ 25 °C Distribution loop entry into processing area or first point of use Monthly pH 5.0 – 7.5
Conductivity Distribution loop entry into processing area or first point of use Monthly μS/cm <10
Total alkalinity Distribution loop entry into processing area or first point of use Monthly mg CaCO3/L <8
Total hardness Distribution loop entry into processing area or first point of use Monthly mg CaCO3/L <1
Bacteria (HPC) Each point-of-use location in the department Monthly CFU/mL <10
Endotoxin Each point-of-use location in the department Monthly EU/mL <10
Equipment interior visual inspection Spray arms, chamber walls, and machine interiors Daily

Adapted summary of the Critical Water monitoring recommendations in ANSI/AAMI ST108:2023, Tables 4 and 6. Refer to the full standard for applicable requirements, methods, and qualifications.

Important distinction: These frequencies apply to routine monitoring at the point of use. ST108 Table 5 separately addresses monitoring at the water generation system, including daily conductivity monitoring for Critical Water.

How Should Critical Water Samples Be Collected?

Collecting a representative sample requires more than choosing the right location.

Sampling procedures should account for the parameters being measured and the conditions of the water system.

A few important considerations include:

  • Use appropriate containers: Follow laboratory instructions for sample containers and preservatives.
  • Follow the correct collection procedure: Flushing, disinfection, aseptic collection, and sample handling may differ depending on the testing objective.
  • Document the sampling conditions: Record the location, date, time, and relevant system information.
  • Protect sample integrity: Follow laboratory requirements for storage, transportation, and holding times.

Different analyses may require different collection procedures. For example, microbiological samples and samples collected for chemical measurements may have different handling requirements.

When Is Monthly Testing Not Enough?

Monthly monitoring provides a routine picture of water quality, but it may not capture every change within a system.

ST108 recognizes that sampling frequency may need to increase when water quality problems occur or risk assessments identify locations requiring closer attention.

Changes in system operation, maintenance activities, unexpected results, or concerns involving low-use areas may warrant additional monitoring.

The goal isn’t simply to collect samples on schedule. It’s to collect meaningful information that helps verify water quality and identify changes before they become recurring problems.

Make Every Sample Count

Effective Critical Water monitoring combines appropriate sampling locations, consistent collection procedures, and testing frequencies informed by ST108 and facility-specific conditions.

At I-2-I Solutions, we support healthcare facilities with professional water sampling and laboratory testing services to help them evaluate water quality and make informed water management decisions.

Healthcare team reviewing a water quality management program

Discover Our Latest
Insights and Articles

Stay informed with our latest thinking on water quality management and compliance.

Knowledge Hub →